1. |
村本 幸央, 内田 孝紀, 渡邉 康一, 大屋 裕二, 複雑地形上での風況予測精度向上に関する研究, 日本流体力学会 年会2020, 2020.09. |
2. |
大神 沙姫, 渡邉 康一, 内田 孝紀, 大屋 裕二, 熱と風を同時利用するウィンドソーラータワーの風洞実験, 日本流体力学会 年会2020, 2020.09. |
3. |
周防 和輝, 渡邉 康一, 内田 孝紀, 大屋 裕二, ウィンドソーラータワーの野外実験による熱と風の同時利用に関する研究, 日本流体力学会 年会2020, 2020.09. |
4. |
澁谷 光一郎, 内田 孝紀, 渡邉 康一, 大屋 裕二, 2基風車ウェイクの干渉作用について, 日本流体力学会 年会2020, 2020.09. |
5. |
David Carrillo Canizalez, 渡邉 康一, 内田 孝紀, 大屋 裕二, 複数のつば付きディフューザー風車を用いたマルチローターシステムの出力性能向上に関する研究, 日本流体力学会 年会2020, 2020.09. |
6. |
Amr M. Halawa, Takanori Uchida, Koichi Watanabe, and Yuji Ohya, Validation Study of Multi-Rotor Systems Using Two Shrouded Wind Turbines, Torque 2020, 2020.10, Multi rotor systems (MRS) have shown a great potential as a future application of wind energy. In this study, the aim is simulating the aerodynamic performance of a an MRS using fully-resolved shrouded wind turbine blades then validating with experimental data. MRS for wind turbine configurations have been studied using both numerical and experimental approaches. Different case studies have been studied and the power output comparison have been reported. The wind lens turbine (WLT) obviously shows a large increase in power output compared to the bare rotor case. Besides, the twin side-by-side (SBS) WLTs shows even larger power increase compared to the case of single WLT by around 20% for computational fluid dynamics (CFD) calculations at the optimum tip speed ratio s/D of around 0.2. The increase in power coefficient in close proximity can be explained by flow interference and gap flow behaviors. Previously, we used simplified models for blade modeling like actuator line method (ALM) and actuator disk method (ADM). However, currently we are improving the accuracy using CFD with full-scale blades with higher grid resolutions. As the number of units for an MRS is increased, the increase in power output becomes larger and larger. This is because that the gap flows between brimmed diffuser-augmented wind turbines (B-DAWT) in a MRS are accelerated and cause lowered pressure regions due to vortex interaction behind the brimmed diffusers. Thus, an MRS with more B-DAWTs can draw more wind into turbines showing higher power output.. |
7. |
大神 沙姫, 渡邉 康一, 内田 孝紀, 大屋 裕二, 熱と風を同時利用するウィンドソーラータワーの発電性能予測法の確立, 日本航空宇宙学会西部支部講演会(2020), 2020.11. |
8. |
澁谷 光一郎,村本 幸央, 内田 孝紀, 渡邉 康一, 松島 啓二, 高田 青, 大規模ウィンドファーム中の風車後流に対するヨーステアリング角度の影響, 日本航空宇宙学会西部支部講演会(2020), 2020.11, It is important to control the wind turbine wakes for efficient operation of large wind farms. The yaw steering method can deflect wakes and is expected to contribute to the generation management of the entire wind farm. In this study, wind tunnel experiments were conducted using a model of a wind turbine to investigate the effects of the yaw steering method on the wakes and the downstream wind turbine output. The wind speed distribution of the wakes in the yaw state was measured. In addition, two wind turbine models were used to investigate the change in power output in the yaw state.. |
9. |
周防 和輝, 渡邉 康一, 内田 孝紀, 大屋 裕二, ウィンドソーラータワーの野外実験モデルにおける性能予測法に関する研究, 日本航空宇宙学会西部支部講演会(2020), 2020.11. |
10. |
David Carrillo Canizalez, 渡邉 康一, 内田 孝紀, 大屋 裕二, マルチローターシステムにおけるレンズ風車の様々な配置に関する研究, 日本機械学会 第98期 流体工学部門 講演会, 2020.11. |
11. |
澁谷 光一郎, 内田 孝紀, 渡邉 康一, 大屋 裕二, 2基の風車のウェイク干渉に関する研究, 日本機械学会 第98期 流体工学部門 講演会, 2020.11. |
12. |
渡邉 康一, 大屋 裕二, 大神 沙姫, 周防 和輝, 内田 孝紀, 熱と風を同時利用するウィンドソーラータワーの発電性能に関する知見, 第42回風力エネルギー利用シンポジウム, 2020.11. |
13. |
周防 和輝, 渡邉 康一, 内田 孝紀, 大屋 裕二, ウィンドソーラータワーの野外実験モデルを用いた発電性能に関する研究, 第42回風力エネルギー利用シンポジウム, 2020.11. |
14. |
大神 沙姫, 渡邉 康一, 内田 孝紀, 大屋 裕二, 太陽光と風力をハイブリッド利用するウィンドソーラータワーの発電性能予測法の提案, 第42回風力エネルギー利用シンポジウム, 2020.11. |
15. |
David Carrillo Canizalez, 渡邉 康一, 内田 孝紀, 大屋 裕二, 様々な配置のマルチローターシステムによるレンズ風車の性能向上に関する研究, 第42回風力エネルギー利用シンポジウム, 2020.11, Four types of MRS arrangements were tested in the wind tunnel. The power output increased compared to a stand-alone turbine. The largest power output increase ratio was achieved on the side-by-side arrangement. An optimal gap and distance in streamwise direction exist in each arrangement. CFD flow visualization shows an accelerated gap flows as well as a generation of a low-pressure zone in the back of the wind turbines. Staggered arrangement CFD results shows that pressure distribution for the side turbines was remarkably lowered compared to the center turbine. |
16. |
澁谷 光一郎, 内田 孝紀, 村本 幸央, 渡邉 康一, 大屋 裕二, 風車後流内の流動現象解明のための風洞実験ならびにCFD その2:ヨーステアリングによる後流の偏向と風車出力への影響, 第42回風力エネルギー利用シンポジウム, 2020.11. |
17. |
澁谷 光一郎, 内田 孝紀,村本 幸央, 渡邉 康一, 大屋 裕二, 風車後流内の流動現象解明のための風洞実験ならびにCFD その1:複数風車後流の相互干渉による影響, 第42回風力エネルギー利用シンポジウム, 2020.11. |
18. |
内田 孝紀, 渡辺 康一, 大屋 裕二, 松島 啓二, 高田 青, 風車ウエイク内の気流性状に関する風洞実験および数値シミュレーション, 第26回風工学シンポジウム, 2020.12. |
19. |
澁谷 光一郎, 内田 孝紀, 渡邉 康一, 大屋 裕二, 数値シミュレーションと風洞実験によるヨーステアリング運転時の風車後流に関する研究, 第34回数値流体力学シンポジウム, 2020.12. |
20. |
@渡邉康一、大屋裕二、@HalawaAmr, 熱と風が同時に与えられたときのウインドソーラータワーの創風性能, 第41回 風力エネルギー利用シンポジウム, 2019.12. |
21. |
@大屋 裕二、@烏谷 隆、@内田 孝紀、@渡邉 康一, つば付きディフューザ風車を用いたマルチロータシステム の野外実験 ー その2 乱れ特性の影響, 第41回 風力エネルギー利用シンポジウム, 2019.12. |
22. |
@渡邉康一、大屋裕二、@HalawaAmr、@内田孝紀, ウインドソーラータワー内部に発生する熱上昇風の数値計算, 第33回 数値流体力学シンポジウム, 2019.11. |
23. |
#齋藤 望、@内田 孝紀、@渡邉 康一、@大屋 裕二、@松島 啓二、@髙田 青, 地表付近の風況予測精度向上のための孤立峰を用いた風洞実験および数値流体シミュレーション, 日本航空宇宙学会西部支部講演会 2019, 2019.11. |
24. |
#藤松 拓弥、@内田 孝紀、@渡邉 康一、@大屋 裕二、@松島 啓二、@髙田 青, 2基風車配置における後流の相互干渉に関する研究, 日本航空宇宙学会西部支部講演会 2019, 2019.11. |
25. |
@渡邉康一、@大屋裕二, ウインドソーラータワーの様々なタワー縦横比におけるエネルギー変換効率, 流体力学会年会 2019, 2019.09. |
26. |
#藤松拓弥、@内田孝紀、@渡邉康一、@大屋裕二、@松島啓二、@高田青, 複数風車配置における後流の相互干渉に関する研究, 流体力学会年会 2019, 2019.09. |
27. |
#斎藤望、@内田孝紀、@渡邉康一、@大屋裕二、@松島啓二、@高田青, 複雑地形上の風況予測精度向上のための孤立峰を用いた風洞実験および数値シミュレーション, 流体力学会年会 2019, 2019.09. |
28. |
Yuji Ohya, Koichi Watanabe, Multi-rotor systems in staggered arrangements using diffuser augmented wind turbines, Wind Energy Science Conference 2019 (WESC2019), 2019.06, Multi-rotor systems(MRSs) are defined as single structures containing more than one rotor. For more power output of MRSs, we examined staggered arrangements of MRSs with brimmed-diffuser augmented turbines (Wind Lens Turbine (WLT)). When the central turbine on staggered arrangement was moved in upwind direction, the output increase was close to a single unit’s value, while the total output of MRS did not change a lot. The changes on the individual power output increases were thought to be due to flow pattern changes of accelerated gap-flows among them. The results showed that staggered arrangements have a potential to make flows around the turbines more effective for their power output.. |
29. |
Koichi Watanabe, Yuji Ohya, Power output enhancement of a ducted wind turbine with various shapes of brim, Wind Energy Science Conference 2019 (WESC2019) , 2019.06, A brimmed-diffuser augmented turbine (called Wind Lens Turbine: WLT) utilizes vortices around the brim actively to enhance its power output. However, the vortices are usually unstable and asymmetric. This study attempted to stabilize the vortices and enhance the power output of WLT. Polygonal brims were investigated in wind tunnel experiments and numerical simulations. As a result, ideas achieved 2% increase of the power output compared with standard (round) WLTs. The numerical simulation unveiled a periodicity existed in the fluctuating vortex structure on a circular brim. Polygonal brims with the same periodic scale were able to suppress the vortex fluctuation and stabilize the vortices effectively. Besides, the larger brim tended to encourage the stabilizing effects.. |
30. |
Koichi Watanabe, Yuji Ohya, Energy conversion efficiency of a wind solar tower, Wind Energy Science Conference 2019 (WESC2019) , 2019.06, A wind solar tower (called WST) is one of wind-power generation plants. WST is composed of four parts; a transparent thermal collector on the ground, a tall tower at the center of the collector, a vortex-generation plate on the top of the tower, and a wind turbine inside the tower. The tower utilizes an updraft generated in the tower to rotate its turbine. Two mechanisms below exist for generating the updraft; i) Solar energy warms the air inside the collector. Then the warm air rises in the tower with its buoyancy. ii) Wind energy generates a vortex above the tower. The low pressure of the vortex sucks up the air inside the tower. Although the first mechanism has already used in a traditional solar tower, the second one is our new idea. Generally, renewable-energy power plants are expected to increase their outputs per unit area. WST has a chance of becoming the most powerful device, due to its advantage over the hybrid utilization of renewable energies. Then we have tried to optimize the tower shape for the further enhancement of its power output. Our previous study showed that a diffuser-shaped tower with a semi-open angle of 4° was efficient. The diffuser-shaped tower demonstrated about 4-5 times power output as large as a cylindrical tower. Recently, we conducted some experiments using towers in several varieties of aspect ratios (AR = h/D). We supplied heat energy to the towers in laboratory experiments and wind energy to them in wind tunnel experiments respectively. In the case of heat utilization, the tower with larger aspect ratio tended to show the high heat energy conversion efficiency (=ηH). Similarly, in the case of wind utilization, the tower with a larger aspect ratio increased the wind energy conversion efficiency (=ηW). However, the tower with the vortex-generation plate achieved high ηW regardless of its aspect ratio. This result suggests that wind energy enables us to gain a large power output with a low tower. The low tower will be built at relatively low cost and contribute to the growth of renewables.. |
31. |
Taiga Murakami, Takanori Uchida, Koichi Watanabe, Yuji Ohya, Researches on the efficiency of multi wind turbines with brimmed diffuser on the staggered arrangement, 10th Kyushu Univ.-KAIST Symposium on Aerospace Engineering, 2018.12. |
32. |
村上大河、内田孝紀、渡邉康一、大屋裕二, スタッガード配置による複数の集風体付き風車の性能向上に関する研究, 第40回 風力エネルギー利用シンポジウム, 2018.12. |
33. |
大屋裕二、烏谷隆、渡邉康一, つば付きディフューザ風車を用いたマルチロータシステムの野外実験, 第40回 風力エネルギー利用シンポジウム, 2018.12. |
34. |
渡邉康一、大屋裕二, 太陽熱と風力を同時利用するウインドソーラータワーの性能, 第40回 風力エネルギー利用シンポジウム, 2018.12. |
35. |
渡邉康一、河原信太郎、大屋裕二, 上空風によるウインドソーラータワーの集風性能にタワー縦横比が与える影響, 第25回 風工学シンポジウム, 2018.12. |
36. |
Koichi Watanabe, Takanori Uchida, Yuji Ohya, Wind solar tower harnessing wind energy and solar energy, The 29th International Symposium on Transport Phenomena (ISTP29), 2018.11, Wind Solar Tower is a new power-generating device using renewable energies. A similar conventional device known as a solar chimney has utilized the solar energy alone. Besides, its generation efficiency was very low. Therefore, we largely improved the generation efficiency by arranging the shape of the tower from the cylinder type to the diffuser type. At the same time, we attached a vortex generation plate on the tower. The plate enabled the tower to utilize not only solar energy but also wind energy. The simultaneous utilization of renewable energies with one device is notable discovery. We tried the optimization of the tower shape by laboratory experiments (including wind tunnel ones) and numerical analysis. As a result, we found that the diffuser tower with 4° is the optimal shape, and we succeeded in wind-converging whose speed inside of the tower was faster than upper-wind speed, using the vortex generator. Numerical analysis contributed significantly to clarify the mechanisms. Eventually, we demonstrated the simultaneous utilization of the renewable energies in field experiments.. |
37. |
村上大河、内田孝紀、渡邉康一、大屋裕二, スタッガード配置による複数の集風体付き風車の性能向上に関する研究, 日本航空宇宙学会西部支部講演会 2018, 2018.11. |
38. |
Koichi Watanabe, Yuji Ohya, Effective utilization of wind energies by wind solar tower, Grand Renewable Energy 2018 International Conference and Exhibition (GRE2018), 2018.06. |
39. |
Yuji Ohya, Koichi Watanabe, A new wind turbine system using multiple rotors with brimmed diffusers (Multi-Lens Turbine), Grand Renewable Energy 2018 International Conference and Exhibition (GRE2018), 2018.06. |
40. |
渡邉康一、大屋裕二、綿加正樹, ウインドソーラータワーが創風する熱上昇風の構造に関する研究, 第39回 風力エネルギー利用シンポジウム, 2017.12. |
41. |
森山喬史、渡邉康一、大屋裕二、内田孝紀, 複数のつば付きディフューザ風車を用いたクラスタシステムの開発, 第39回 風力エネルギー利用シンポジウム, 2017.12. |
42. |
森山喬史、内田孝紀、渡邉康一、大屋裕二, 複数の集風体付き風車を有するクラスタシステムの開発, 日本航空宇宙学会西部支部講演会 2017, 2017.11. |
43. |
河原信太郎、内田孝紀、渡邉康一、大屋裕二, ウインドソーラータワーの発電性能向上に関する研究, 日本航空宇宙学会西部支部講演会 2017, 2017.11. |
44. |
井上諒、内田孝紀、大屋裕二、渡邉康一, 複雑地形における地表付近の風況予測精度向上に関する研究, 日本航空宇宙学会西部支部講演会 2017, 2017.11. |
45. |
Yuji Ohya, Koichi Watanabe, Multi-Rotor System Using Brimmed-Diffuser Wind Turbines for Power Output Increase, 15th International Energy Conversion Engineering Conference, AIAA Propulsion and Energy Forum, 2017.07. |
46. |
Yuji Ohya, Akio Munakata, Koichi Watanabe, Power Output Performance of Clustered, Diffuser Augmented Wind Turbines - Multi Rotor System Using Wind-Lens Turbines -, Wind Energy Science Conference 2017 (WESC2017), 2017.06. |
47. |
Koichi Watanabe, Yuji Ohya, A Wind Solar Tower Harnessing Sunshine and Wind Energies, Wind Energy Science Conference 2017 (WESC2017), 2017.06, In 1989, a pilot plant of a solar chimney was erected in Manzanares, Spain, to evaluate the feasibility of the solar tower as a new source of renewable energies. Since then, the solar tower was discussed in the press and academic research, but no commercial plant succeeded the development. A reason for this could be very low efficiency, i.e., very low power output compared with other renewable energy production systems. However, a solar tower that can generate electricity in a simple structure, and enables easy and less costly maintenance, has considerable advantages. A solar tower consists mainly of three components. The collector area is a glass roof, above ground with increasing height towards the center. Attached to the center of the collector is a vertical tower inside which a wind turbine is mounted at the lower entry into the tower. When solar radiation heats the ground through the glass roof, the uprising warm air is guided to the center into the tower. To improve the efficiency in power production for a solar tower, we focused on the shape of the tower and modified the structure from a conventional cylindrical type to a diffuser-type tower. This modification is considered to combine two mechanisms. Firstly, the mechanism to “Generate Wind” which becomes effective when solar thermal energy is available, and secondly the mechanism to “Converge Wind” which becomes effective when wind passes the top end of the diffuser even when solar thermal energy is not available. For a new power generation system using both of wind and solar energies, we named “Wind Solar Tower (WST)”. By combining these two independent concepts which complement one and another, a profitable energy availability power generation system is expected, that is capable of a larger power generation compared to the original solar tower prototype and much larger capacity factor. As a result of fluid dynamic shape optimization, a diffuser-shaped tower shows an increase in the updraft speed of a scaled model. A remarkable improvement in the power output of the internal wind turbine as much as 4-5 times compared to the cylindrical tower is obtained (Fig.1). Based on the two kinds of laboratory experiments, we are now making a field experiment using a prototype of WST with 10m tower height (Fig.2). We have elucidated that the thermal updraft speed is proportional to the root of tower height and temperature difference between the collector inside and the ambient aloft. In the present research, we propose a new renewable energy device that can harness both sunshine and wind energies. It is now showing a high potentiality, reaching 50 times in power output compared to the Manzanares. Furthermore, almost similar amount of power output by wind aloft over the tower is expected depending on wind condition of the site.. |
48. |
渡邉康一、福富翔、大屋裕二, 上空風によって効果的に集風するウインドソーラータワーの形状に関する研究, 平成29年度 日本風工学会 年次研究発表会, 2017.05. |
49. |
渡邉康一、福富翔、烏谷隆、大屋裕二, 上空風によって発生するウインドソーラータワー内部の上昇風に関する研究, 第38回 風力エネルギー利用シンポジウム, 2016.12. |
50. |
宗像秋生、ウリゴルテンボット、渡邉康一、烏谷隆、大屋裕二, つば付きディフューザ風車を用いたマルチロータシステムにおける発電出力・抗力特性, 第38回 風力エネルギー利用シンポジウム, 2016.12. |
51. |
渡邉康一、大屋裕二、烏谷隆, 垂直軸型風車の駆動原理の解明と集風装置の適用による高出力化, 第21回 風工学シンポジウム, 2010.12. |
52. |
Shuhei Takahashi, Yuji Ohya, Takashi Karasudani, Koichi Watanabe, Numerical and Experimental Studies of Airfoils Suitable for Vertical Axis Wind Turbines and an Application of Wind-Energy Collecting Structure for Higher Performance, The Fourth International Symposium on Computational Wind Engineering (CWE2006), 2006.07. |
53. |
渡邉康一、高橋周平、大屋裕二、烏谷隆、渡辺公彦, 垂直軸型風車の駆動メカニズムの解明と2次元風レンズ体(集風装置)の適用, 平成17年度 日本風工学会 年次研究発表会, 2005.04. |
54. |
渡邉康一、大屋裕二、烏谷隆、渡辺公彦, 直線翼垂直軸型風車への2次元風レンズ体(集風装置)の適用, 第26回 風力エネルギー利用シンポジウム, 2004.11. |
55. |
渡邉康一、大屋裕二、烏谷隆、渡辺公彦, 集風構造体の垂直軸型風車への適用, 日本航空宇宙学会西部支部講演会 2004, 2004.10. |
56. |
渡邉康一、大屋裕二、烏谷隆、久米宏明, つば付きディフューザ風車の開発と周辺流解析, 流体力学会年会 2004, 2004.08. |
57. |
Koichi Watanabe, Yuji Ohya, Takashi Karasudani, Kimihiko Watanabe, Development of a Wind Turbine Generating High Output Power, The 5th Korea/Japan Joint Workshop on Aeronautics and Astronautics, 2004.07. |